AirFit F20 Support
Item Code : 63400, 63401, 63402, 63403, 63404

Select model:

Sizing the AirFit F20

  1. To comfortably fit a broader range of patients, AirFit F20 features an entirely new cushion design. To make crosswalking your existing patients easier, we recommend using our sizing guide – included in each AirFit F20 box and specifically designed to help patients find the right fit.
  2. The arrow of your sizing guide should align with the top of your patient’s nasal bridge. The segment of the guide corresponding with the crease below your patient’s lower lip will indicate their best fit. If a patient falls between sizes, we recommend selecting a larger option for greater comfort.
  3. AirFit F20 has three cushion sizes – small, medium and large. The modular design of the AirFit F20 means each size cushion easily clicks into the same F20 mask frame.
  4. You can also download a copy of our sizing guide here.

Fitting the AirFit F20

  1. Unclip the magnetic clips.
  2. With your patient holding the mask towards their face, slide the headgear over the back of their head.
  3. Reclip the magnetic clips.
  4. Once your patient’s headgear and mask are properly fitted, you can use the upper and lower headgear straps to help fine-tune their fit. This is also a good opportunity for your patient to reseat their cushion for comfort. When fitting is concluded, the cushion membrane should be fitting comfortably over your patient’s nasal bridge.
  5. For additional information on mask maintenance and care, you can also visit the Supporting your patients section.

Getting started with therapy
Here are some links to help your patients get on the right track with their sleep therapy.

Your therapy basics

The how, what, where and why…

The benefits of therapy

What does therapy do for you…

Think positive

Some helpful tips…

Fitting the AirFit F20

  1. Unclip the magnetic clips.
  2. With your patient holding the mask towards their face, slide the headgear over the back of their head.
  3. Reclip the magnetic clips.
  4. Once your patient’s headgear and mask are properly fitted, you can use the upper and lower headgear straps to help fine-tune their fit. This is also a good opportunity for your patient to reseat their cushion for comfort. When fitting is concluded, the cushion membrane should be fitting comfortably over your patient’s nasal bridge.
  5. For additional information on mask maintenance and care, you can also visit the Supporting your patients section

Managing leak with your AirFit F20

  1. Leak often occurs when your mask’s seal is compromised by movement, incorrect fitting or improper sizing.
  2. To find a source of leak, run your finger along the edge of your mask’s seal. Once located, adjust your headgear.
  3. Resolve any leak in the upper part of your mask by adjusting your upper straps.
  4. Resolve lower mask leak with your lower straps.
  5. If leak persists, reseal by briefly pulling your mask away from your face, letting your cushion reinflate, and resettling your mask cushion so the cushion membrane is sitting at the top of your nasal bridge.
  6. If leak continues, you may need a different size mask. Try our sizing guide or speak to your healthcare provider about getting a different size mask.

Cleaning your AirFit F20 (Daily)

  1. Disassemble mask.
  2. Rinse frame, elbow and cushion under running water. Clean each component with a soft brush.
  3. Soak components in warm water with mild liquid detergent for up to ten minutes.
  4. Shake components in water.
  5. Brush moving parts of elbow and around vent holes.
  6. Brush areas of frame where arms connect, and inside and outside the frame where the elbow connects.
  7. Rinse components under running water.
  8. Leave components to air dry out of direct sunlight – making sure to squeeze the arms of the frame to ensure excess water is removed.

Cleaning your AirFit F20 (Weekly)

  1. Disassemble mask. EasyClick magnets can remain attached to headgear during cleaning.
  2. Handwash headgear in warm water with mild liquid detergent.
  3. Rinse headgear under running water. Inspect to ensure headgear is clean and detergent free. Wash and rinse again, if necessary.
  4. Squeeze headgear to remove excess water.
  5. Leave headgear to air dry out of direct sunlight.

Reassemble the AirFit F20

  1. Attach cushion to frame.
  2. Attach the EasyClick Magnets.
  3. Connect upper headgear straps.
  4. Connect elbow to mask frame.

Disassemble the AirFit F20

  1. Remove elbow from frame.
  2. Unclip the magnetic clips.
  3. Undo upper headgear tabs.
  4. Pull strapping away from frame.
  5. Pull cushion away from frame.

Getting started with therapy
Here are some links to help your patients get on the right track with their sleep therapy.

Your therapy basics

The how, what, where and why…

The benefits of therapy

What does therapy do for you…

Think positive

Some helpful tips…

Still have a question?
1 (800) 424-0737