AirFit N30i
Patients and Families > Support > Masks > AirFit N30i

AirFit N30i Support
Item Codes: 63815, 63816

Support

Packages

There are two starter packs, each of which is delivered with 1 frame and 2 cushions as follows:

1. Small starter pack: 1 small frame, 2 cushions (small and medium sizes)

2. Standard starter pack: 1 standard frame, 1 small cushion, 1 medium cushion

Please note: Standard frame is bigger than small frame.

Two additional cushions can be ordered as spare parts:

1.Small wide cushion (SW size): for small flat noses

2.Wide cushion (W size): for large flat noses

Sizing frame

Step 1 -In general, men should select the standard frame size and women should select the small frame size. These are general recommendations that can be disregarded if you feel that you have a smaller/larger face than average. 

Step 2 -The frame should sit on the top of the head, like a headband. If the frame is too small, it will feel tight and sit too close to your forehead. If the frame is too large, it will feel loose and sit too far back on your head.

Sizing cushion

Step 1 -Print the template in the right dimensions (check the scale).

Step 2 -Place the template below your nose, perpendicular to your face. If you have a narrow nose, start with the blue/red side of the template. If you have a wide nose, start with the black/purple side of the template.

Step 3 -Look into a mirror and assess whether your nose falls inside or outside the margins on the template. If you are between two sizes, choose the larger one.

Step 4 -If your nose is size S (red) or M (blue), select the appropriate cushion from your starter pack. If your nose is SW (purple) or W (black) then you will need to order the cushion as a spare part.

Fitting

Step 1 -Pull the frame and headgear over your head until the elbow is positioned on top of your head, like a headband, and the headgear is behind your head.

Step 2 -Place the cushion under your nose with one hole under each of your nostrils and the small membrane sitting comfortably between them.

Step 3 -Tighten or loosen the headgear until the cushion fits comfortably under your nose. If you feel that your nose is being pushed up, the headgear is too tight and you should loosen the straps. If you feel that the cushion is sliding around under your nose, the headgear is too loose and you should tighten the straps.

Step 4 -Squeeze the side buttons on the elbow and detach from the frame. Connect the air tubing from your device to the elbow, then reattach to the frame.

 

These instructions are for general information purpose only. For full details please consult the user guide.

Fitting

Step 1 -Pull the frame and headgear over your head until the elbow is positioned on top of your head, like a headband, and the headgear is behind your head.

Step 2 -Place the cushion under your nose with one hole under each of your nostrils and the small membrane sitting comfortably between them.

Step 3 -Tighten or loosen the headgear until the cushion fits comfortably under your nose. If you feel that your nose is being pushed up, the headgear is too tight and you should loosen the straps. If you feel that the cushion is sliding around under your nose, the headgear is too loose and you should tighten the straps.

Step 4 -Squeeze the side buttons on the elbow and detach from the frame. Connect the air tubing from your device to the elbow, then reattach to the frame.

 

These instructions are for general information purpose only. For full details please consult the user guide.

 

Assembly

Step 1 -Ensure you have all the mask components and parts together.

Step 2 -Connect the elbow to the frame.

Step 3 -Thread the left end of the headgear into the left side of the frame and fasten the tab.

Step 4 -Thread the right end of the headgear into the right side of the frame and fasten the tab.

Step 5 -Insert the ends of the frame into the cushion, ensuring that the arrows on the cushion and frame are aligned. 

 

Note: If the elbow ring detaches, re-insert into the top of the frame.

Disassembly

Step 1 -Ensure your mask is disconnected from your machine.

Step 2 -Pull the cushion out from one end of the frame. 

Step 3 -Pull the cushion out from the other end of the frame.

Step 4 -Unfasten the headgear tab from one side and pull it out of the frame.

Step 5 -Unfasten the headgear tab from the other side and pull it out of the frame.

Step 6 -Squeeze the side buttons on the elbow and pull up to release it from the frame.

Daily cleaning

Step 1 -Take the cushion off the frame as per disassembly instructions.

Step 2 -Soak the cushion in warm water and a mild liquid detergent.

Step 3 -Clean the cushion and its vent holes inside and out with a soft bristle brush. 

Step 4 -Rinse the cushion thoroughly under running tap water.

Step 5 -Leave the cushion to air dry away from direct sunlight.

 

These instructions are for general information purposes only. For full details please consult the user guide.

Managing leak

Step 1 -Locate where the air is escaping from, which is typically above or below the cushion.

Step 2 -Adjust the cushion by gently pulling it away from your face and letting it reseal itself.

Step 3 -Adjust the headgear as needed to achieve a more secure seal. 

Step 4 -Check the frame is secure and that the mask elbow and tubing are not pulling on the mask.

 

Consult a qualified health professional if you experience a recurrent leak problem.

 

Daily cleaning

Step 1 -Take the cushion off the frame as per disassembly instructions.

Step 2 -Soak the cushion in warm water and a mild liquid detergent.

Step 3 -Clean the cushion and its vent holes inside and out with a soft bristle brush.

Step 4 -Rinse the cushion thoroughly under running tap water.

Step 5 -Leave the cushion to air dry away from direct sunlight.

 

Weekly cleaning

Step 1 -Disassemble the mask into its components as per disassembly instructions.

Step 2 -Soak each of the components (headgear, elbow and frame) in warm water and a mild liquid detergent.

Step 3 -Clean the elbow and frame with a soft bristle brush and the headgear with your hands.

Step 4 -Rinse each of the components thoroughly under running tap water.

Step 5 -Squeeze the headgear and the sleeves on the frame with a clean towel to remove excess water.

Step 6 - Leave each of the components to air dry away from direct sunlight.

 

These instructions are for general information purpose only. For full details please consult the user guide.

Do you have a question?

Phone number : 0800 917 7071 operationsuk@resmed.co.uk