AirFit F30AirFit F30 under the nose CPAP full face mask.
AirFit F30

AirFit F30 Support
Item Codes: 64110, 64111

Support

Packages

There are two mask systems, each of which is delivered with 1 headgear and 1 cushion as follows:

1.Small mask system: 1 single-size headgear, 1 small cushion

2.Medium mask system: 1 single-size headgear, 1 medium cushion

Please note: The headgear is single-size but is fully adjustable at 5 points and features straps and magnets for ease of use and adjustment.

Sizing cushion

Step1 -Print the template in the right dimensions (check the scale).

Step2 -Place the template below your nose, perpendicular to your face.

Step3 -Assess the width of your nose and the corresponding cushion size. If your nose sits within the red border, choose the small cushion. If your nose extends into the blue border, choose the medium cushion.

Fitting

Step 1 -Ensure the magnets are open on the lower headgear straps.

Step 2 -Bring the cushion under your nose with one hole under each of your nostrils and the small membrane sitting comfortably between them.

Step 3 - Pull the headgear over your head while holding the cushion securely under your nose.

Step 4 -Bring the lower headgear straps under your ears and attach each magnetic clip to the frame.

Step 5 - Adjust the upper headgear straps until the mask is secure.

Step 6 - Adjust the lower headgear straps until the mask is secure.

Step 7 -Adjust the headgear strap on the top of your head until the mask is secure and the strap sits close to the centre of your head. If you feel that your nose is being pushed up, the headgear is too tight and you should loosen the straps. If you feel that the cushion is sliding around under your nose, the headgear is too loose and you should tighten the straps.

Step 8 -Connect the air tubing from your device to the mask elbow.

Hair management

Step1 - Long untied hair back should not sit underneath the headgear.

Step2 -Long untied hair should be pulled through the headgear and back behind your ears.

Step3 - Ponytails should not sit underneath the headgear.

Step4 - Ponytails should be pulled through the headgear and behind your head.

These instructions are for general information purpose only. For full details consult the user guide.

Fitting

Step 1 -Ensure the magnets are open on the lower headgear straps.

Step 2 -Bring the cushion under your nose with one hole under each of your nostrils and the small membrane sitting comfortably between them.

Step 3 - Pull the headgear over your head while holding the cushion securely under your nose.

Step 4 -Bring the lower headgear straps under your ears and attach each magnetic clip to the frame.

Step 5 -Adjust the upper headgear straps until the mask is secure

Step 6 - Adjust the lower headgear straps until the mask is secure.

Step 7 - Adjust the headgear strap on the top of your head until the mask is secure and the strap sits close to the centre of your head.

Step 8 -Connect the air tubing from your device to the mask elbow.

Assembly

Step 1 - Check that you have all the mask components as pictured.

Step 2 - Ensure that the ResMed logo on the headgear is facing outwards.

Step 3 -Thread the left upper headgear into the left side of the frame and fasten the Velcro tab.

Step 4 -Thread the right upper headgear into the right side of the frame and fasten the Velcro tab.

Step 5 -Align the cushion with the frame and connect them together.

Step 6 -Connect the elbow to the frame.

Disassembly

Step 1 -Ensure your mask is disconnected from your machine.

Step 2 -Unfasten the left upper headgear strap and pull it away from the frame.

Step 3 -Unfasten the right upper headgear strap and pull it away from the frame.

Step 4 -Squeeze the side buttons on the elbow and detach it from the frame.

Step 5 - Pull the cushion away from the frame.

Quick release

Step 1 -First stop your device.

Step 2 -Disconnect the elbow and attached tubing from your mask by squeezing the elbow's buttons and pulling it out.

Step 3 -Reconnect the elbow and tubing by clicking it back into the mask.

Step 4 -Restart your therapy.

Daily cleaning

Step 1 -Disassemble the mask into its components, and place the headgear aside.

Step 2 -Soak and agitate the mask elbow, frame and cushion in warm soapy water for at least one minute.

Step 3 - Hand wash each of the components with a soft bristle brush.

Step 4 -Rinse each of the components under running water to remove any suds.

Step 5 - Leave the components to air dry away from direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.

Managing leak

Step 1 - You will first need to check where the leak is coming from.

Step 2 - You can try resealing the mask by pulling it away from your face and letting it settle back into position.

Step 3 - Adjust the top headgear strap to correct minor leaks.

Step 4 -Adjust the upper straps to correct leaks from the upper areas of the mask.

Step 5 - Adjust the lower straps to correct leaks from the lower areas of the mask.

Step 6 - Check that both the frame and headgear are secure and comfortable.

Consult a qualified health professional if you experience a recurrent leak problem.

Daily cleaning

Step 1 - Disassemble the mask into its components, and place the headgear aside.

Step 2 - Soak and agitate the mask elbow, frame and cushion in warm soapy water for at least one minute.

Step 3 -Hand wash each of the components with a soft bristle brush.

Step 4 -Rinse each of the components under running water to remove any suds.

Step 5 - Leave the components to air dry away from direct sunlight.

Weekly cleaning

Step 1 -Take the headgear off the mask and set aside.

Step 2 -Soak and agitate the headgear in warm soapy water for at least one minute.

Step 3 -Hand wash the headgear by gently rubbing and squeezing it.

Step 4 -Rinse the headgear under a running water to remove any suds, and then squeeze it to remove excess water.

Step 5 -Leave the headgear to air dry away from direct sunlight.

Mask Inspection

Step 1 -Examine the mask system and familiarize yourself with its components.

Step 2 -Disassemble the mask as per User Guide instructions.

Step 3 -Examine the headgear by checking and pulling lightly on its straps.

Step 4 -Examine the elbow inside and out for damage, paying attention to the inner flaps and vent holes.

Step 5 - Examine the frame on both sides for cracks and damage.

Step 6 -Examine the cushion inside and out for tears and damage.

Step 7 - Reassemble the mask as per User Guide instructions.

These instructions are for general information purpose only. For full details consult the user guide.

Do you have a question?

Phone number : 0800 917 7071 operationsuk@resmed.co.uk