AirFit N20 Support
Patients and Families > Support > Masks > AirFit N20 Support

AirFit N20 Support
Item Codes: For more information contact your regional home care provider.

Select model:

Support

Sizing for your AirFit N20

You can print your ResMed sizing guide here

Remember to print to scale, as you’ll have to cut out your guide from the document you print. If you prefer, we can also send you a sizing guide by mail, simply send us your posting details.

Once you have your sizing guide:

use a mirror and hold the sizing guide to your face.

Try fitting your nose into each sizing option. The most comfortable one will provide you with the best fit.

As an alternative to using a sizing guide, you can also measure your nose width with a ruler. Different measurements correspond to the following sizes:

Between 23-37 mm: Small

Between 30-45 mm: Medium

?Between 45-55 mm: Large

Fitting your AirFit N20

Step 1 - Unclip the EasyClickTM Magnets.

Step 2 - With the mask held against your face, pull the headgear over your head.

Step 3 - Bring each of the magnets up to meet their corresponding clips on the frame.

Step 4 - Adjust the tabs on the upper headgear straps.

Step 5 - Adjust the tabs on the lower headgear straps.

Step 6 - With your device still switched off, connect your device tubing to your mask elbow.

Step 7 - Connect the elbow to your mask.

Step 8 - Switch on your therapy device..

These instructions are for general information purpose only. For full details consult the user guide.

Getting started with therapy
Get on the right track with your sleep therapy.

Your therapy basics

The how, what, where and why...

The benefits of therapy

What does therapy do for you..

Think positive

Some helpful tips

Fitting your AirFit N20

Step 1 - Unclip the EasyClickTM Magnets..

Step 2 - With the mask held against your face, pull the headgear over your head.

Step 3 - Bring each of the magnets up to meet their corresponding clips on the frame.

Step 4 - Adjust the tabs on the upper headgear straps.

Step 5 - Adjust the tabs on the lower headgear straps.

Step 6 - With your device still switched off, connect your device tubing to your mask elbow.

Step 7 - Connect the elbow to your mask.

Step 8 - Switch on your therapy device.

Disassembling your AirFit N20

Step 1 - Remove elbow from frame.

Step 2 - Unclip the EasyClick Magnets.

Step 3 - Undo upper headgear tabs.

Step 4 - Pull strapping away from frame.

Step 5 - Pull cushion away from frame.

Cleaning your AirFit N20 (Daily)

Step 1 - Disassemble mask.

Step 2 - Soak cushion, elbow and short tubing in warm water (approximately 86°F/30°C) with mild liquid detergent for up to ten minutes. To ensure a thorough clean, shake components in water.

Step 3 - Clean components with a soft-bristle brush.

Step 4 - Rinse components under warm water. Inspect each component to ensure that each is clean and free of detergent residue. Wash and rinse again, if necessary.

Step 5 - Leave mask components to air dry out of direct sunlight.

Assembling your AirFit N20

Step 1 - Attach cushion to frame.

Step 2 - Attach the EasyClick Magnets.

Step 3 - Connect upper headgear straps.

Step 4 - Connect elbow to mask frame.

Haircare Tips for AirFit N20

These instructions are for general information purpose only. For full details consult the user guide.

Managing leak with your AirFit N20

Leak often occurs when your mask’s seal is compromised by movement, incorrect fitting or improper sizing.

To find a source of leak, run your finger along the edge of your mask’s seal to locate where air is escaping.

Leak often occurs when your mask’s seal is compromised by movement, incorrect fitting or improper sizing.

Leak in the lower part of the mask can be resolved with your lower straps.

If leak persists, reseal by briefly pulling your mask away from your face and letting your cushion reinflate..

If these steps do not resolve the issue, you may need a different size mask. Try using our sizing guide or speaking to your healthcare provider about different size masks.

Maintaining your AirFit N20

To maintain optimum therapy performance, your mask should be checked regularly for signs of damage and deterioration.

When cleaning your mask, you should also check each component for damage. Your cushion, frame, tubing, elbow and headgear should all be regularly checked for cracks and tears.

If any component of your mask is cracked or torn, it may be damaged and in need of replacement.

It’s also important to regularly replenish your mask cushion.

Cleaning your AirFit N20 (Daily)

Step 1 - Disassemble mask.

Step 2 - Soak cushion, elbow and short tubing in warm water (approximately 86°F/30°C) with mild liquid detergent for up to ten minutes. To ensure a thorough clean, shake components in water.

Step 3 - Clean components with a soft-bristle brush.

Step 4 - Rinse components under warm water. Inspect each component to ensure that each is clean and free of detergent residue. Wash and rinse again, if necessary.

Step 5 - Leave mask components to air dry out of direct sunlight.

Cleaning your AirFit N20 (Weekly)

Step 1 - Disassemble mask. EasyClick Magnets can remain attached to headgear during cleaning.

Step 2 - Soak frame and headgear in warm water (approximately 86°F/30°C) with mild liquid detergent for up to ten minutes. To ensure a thorough clean, shake frame and headgear in water..

Step 3 - Rinse both components in clean water. Squeeze each repeatedly to ensure detergent is fully removed. Inspect each component to ensure that each is clean and free of detergent residue. Wash and rinse again, if necessary..

Step 4 - Rinse components under warm water. Inspect each component to ensure that each is clean and free of detergent residue. Wash and rinse again, if necessary.

Step 5 - Squeeze each component repeatedly to remove excess water.

Step 6 - Leave both components to air dry out of direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.

Replenishment

ResMed recommend regulary replacing your components to ensure optimum mask performance.

  • Every 6 months*

    Cushion

  • Every 6 months*

    Tubing

  • Every 12 months*

    Headgear

*

*Replacement cycles may vary depending on your insurance—contact your ResMed representative for more information.

Accessories 

ResMed offers a range of accessories and spare parts for our sleep apnea therapy and CPAP masks, devices and humidifiers.

Do you still have a question?

Contact us